Jump to content

trojanko

Участники
  • Content count

    5
  • Joined

  • Last visited

Community Reputation

0 Neutral
  1. The company is Mining Crazy has developed firmware for ASIC Antminer S17/T17 pro and Antminer. You can already download and install it, make your miner even more powerful !! We are glad to present you our finished firmware for Antminer S17/S17pro and T17, the results of which are impressive ! Antminer S17 / T17 Overclocking performance ~+30% The possibility of downvolt ~-15-25% This Antminer S17(normal) to 70-80Th/s (~3100-3760w) Ant antminer T17 up to 55 th / s (consumption ~ 3000W) (Attention! firmware on T17 works in test mode, in order to avoid breakdowns it is recommended to do overclocking to 45th !) All firmware comes with Dev Fee 2.8%. You can download the firmware here:https://asic-firmware.com/firmware-for-antminer-s17-t17-crmi/ So, what do you get with our firmware : Air-cooled overclocking capability up to 80 TH/s for S17 and 55 TH/s for T17 2.Possibility of acceleration on immersion cooling up to 100 TH / s and up to 65 TH / s for T17 3.Current information of each chip (green, orange, red) 4.Overclocking ranges (choose the overclocking option you want) 5.Options for downvolt (reduction of power consumption) 6.Individual overclocking each Board separately (overclocking and voltage)Individual overclocking of each chip ( thanks to this, you can achieve maximum ASIC speed and stable operation) 7.AUTO TUNING (automatic frequency selection + evaluation of chips in automatic mode, increasing the life of the miner) 8.Reducing the number of HW errors than in Bitmain firmwareFunction of switching off of fans at immersion cooling 9.Function create workers + install firmware + transfer config to an unlimited number of miners in the same network at the same time 10.The ASIC BOOST function is installed (reduction of power consumption on average up to 15-25% due to the optimal operation of the ASIC at its current hashrate level) 11.Function of automatic check and destruction of ASIC on viruses and malware ( these cases happen at purchase of the B. U. of the equipment, up to replacement of the control Board of falling of ASIC) 12.Output function of electricity consumption (wattmeter) 13.ASIC search function (blinking Led lights) 14.Mass password change, SSH port and SSH port disconnect function 15.The “sleep mode” function when it is turned on, mining stops and the fans fall to the minimum speed. 16.The ability to disable electricity consumption when resetting the Internet or pool addresses ( on the firmware Bitmain miner continues to consume electricity) 17.Redesigned algorithm of fans (quiet start, maintaining the temperature on the chips, increasing the life of fans) For support please contact our telegram support channel https://t.me/asicfirmware So same in contacts telegrams on nicknames : @trojanko, @onizak
  2. Компания Сrazy Mining разработала прошивку для ASIC Antminer S17/pro и Antminer T17. Вы уже можете скачать и установить ее, сделайте свой майнер еще мощнее !! Рады вам представить нашу готовую прошивку для Antminer S17/S17pro и Т17, результаты которой впечатляют ! Разгон Antminer S17 / T17 Производительность ~+30% Возможность даунвольта ~-15-25% Antminer S17(обычный) до 70-80Th/s (~3100-3760w) Antminer T17 до 55 Th/s (Потребление ~ 3000W) ( Внимание ! прошивка на Т17 работает в тестовом режиме, во избежании поломок рекомендуется делать разгон до 45th ! ) Прошивка включает Dev Fee 2.8%. Скачать прошивку вы можете перейдя по ссылке: https://asic-firmware.com/ru/proshivka-dlya-antminer-s17-t17/ Итак, что Вы получаете с помощью нашей прошивки : 1. Возможность разгона на воздушном охлаждение до 80 TH/s для S17 и 55 TH/s для Т17 2.Возможность разгона на иммерсионном охлаждение до 100 TH/s и до 65 TH/s для T17 3.Текущую информацию каждого чипа (зеленый, оранжевый, красный) 4.Диапазоны разгона (выбирайте тот вариант разгона который вы хотите) 5. Варианты для даунвольта (уменьшение электропотребления) 6.Индивидуальный разгон каждый платы по отдельности (разгон и вольтаж) 7. Индивидуальный разгон каждого чипа ( благодаря этому можно добиться максимальной скорости асика и стабильной работы) 8. AUTO TUNING ( автоматический подбор частоты + оценка работы чипов в автоматическом режиме, повышение срока работы майнера) 9.Уменьшение количества ошибок HW чем в прошивке от Bitmain 10. Функция отключения вентиляторов при иммерсионном охлаждении 11. Функиця создания воркеров + установки прошивки + перенос конфига на неограниченное количество майнеров в одной сети одновременно 12. Установлена функция ASIC BOOST (уменьшение расхода электроэнергии в среднем до 15-25% за счет оптимальной работы асика при ее текущем уровне хешрейта) 13. Функция автоматической проверки и уничтожение ASIC на вирусы и вредоносное ПО ( данные случаи бывают при покупки Б.У. оборудования , вплоть до замены контрольный платы упавления асика) 14. Функция вывода потребления электричества (ваттметр) 15. Функция поиска асика (моргание Led лампами) 16. Функция массовой смены пароля, порта SSH и отключения порта SSH 17. Функция «режим сна» при ее включении, майнинг останавливается и вентиляторы опускаются до минимальных оборотов. 18. Возможность отключения потребления электричества при сбросе интернета или адресов пула ( на прошивке Bitmain майнер продолжает потреблять электричество) 19. Переделан алгоритм работы вентиляторов (тихий старт, поддержание температуры на чипах, увеличение срока работы вентиляторов) По вопросам установки пишите в наше телеграмм канал поддержки https://t.me/asicfirmware Так же в контакты телеграмм по никам : @trojanko, @onizak
  3. Bitmain company released software (firmware) for i S9 asics on the Sha256 algorithm, which allows to increase the network's hashrate, with reduction of electricity to 1000w on a standard power supply. The Crazy Mining team was able to improve Bitmain’s ASIC Boost. Crazy Mining's ASIC Boost firmware allows you to overclock the S9 / S9j / S9i models up to 17.5 th / s with a 1800w power consumption. IMPORTANT! This firmware works on the next pools, the list is incomplete: https://asicboost.dance/ Possible overclocking: 17 th / s - 1600w - Bitmain power supply is suitable. 17-18.5 th / s and above 1700-2100w - more powerful power supply is needed 2400w power supply. ( Firmware support): https://t.me/asicfirmware ( Download firmware): https://asic-firmware.com/firmware-for-antminer-s9-i-j-17-5-th-s/ (Step by step manual): https://asic-firmware.com/instructions-for-firmware-antminer-s9/ Alternative firmware for Antminer s9 V1 updates : 1) Stability improvement 2) You can choose between a complete restart of the ASIC and the restart of only the cgminer in Autotune section. 3) Besides automatic system for viruses checking there is now a manual checking and disinfection in the Security section. This also works against the new AntBuild virus 4) Fixed connection to the monitor Anthill.farm 5) The new Find Miner function to the config multiplier to search for more miners simultaneously 6) New format of downloading the log file in txt 7) New function “sleep mode” – mining stops and the fans drop to minimal. Available in the config multiplier. 8) No more problem with DevFee error exit 9) Fan control, turn off fan control for immersion immersion cooling - no more need for a cooler emulator.
  4. Crazy Mining company released software (firmware) for L3+ asics on the Scrypt algorithm, which allows to increase the machines hashrate up to 640 MH/s, with reduction of electricity. L3+ firmware by Crazy Mining allows you to overclock L3+ models in 3 modes: 1) Reduces power consumption up to 600 watts with a standard power of 504 MH / s 2) Overclocking up to 580 MH / s with power consumption of 800 watts 3) Overclocking up to 640 MH / s with power consumption of 1000-1100 watts After installing the firmware, press: CTRL + F5 to update the firmware or make a reboot by disconnecting L3+ from the power supply. Version 002 updates: -Automatic settings by consumption or performance profile; -The choice of voltage and frequency to the payload automatically and manually; -Frequency tuning with chips, the ability to start the work of faulty boards; -Fan control, turn off fan control for immersion immersion cooling - no more need for a cooler emulator. ( Firmware support): https://t.me/asicfirmware ( Download firmware):https://asic-firmware.com/ru/proshivka-dlya-antminer-l3/
  5. Crazy Mining company released software (firmware) for t9+ asics on the Sha256 algorithm, which allows to increase the network’s hashrate, with reduction of electricity. ASIC Boost firmware by Crazy Mining allows you to overclock T9 + models up to 14.5 th / s with an energy consumption of 1600w. Free custom firmware allows you to fully unlock all the possibilities of your miner! IMPORTANT! This firmware works on the next pools, the list is incomplete: https://asicboost.dance/ Possible overclocking: 14.5 th / s – 1600w – Bitmain power supply is suitable. ( Firmware support): https://t.me/asicfirmware ( Download firmware): https://asic-firmware.com/firmware-for-antminer-t9-t9-crmi/ Alternative firmware for Antminer T9 + V009 update : 1) Stability improvement 2) You can choose between a complete restart of the ASIC and the restart of only the cgminer in Autotune section. 3) Besides automatic system for viruses checking there is now a manual checking and disinfection in the Security section. This also works against the new AntBuild virus 4) Fixed connection to the monitor Anthill.farm 5) The new Find Miner function to the config multiplier to search for more miners simultaneously 6) New format of downloading the log file in txt 7) New function “sleep mode” – mining stops and the fans drop to minimal. Available in the config multiplier. 8) No more problem with DevFee error exit
×